Using the cinematic camera - Revision history

DeamonHunter at 03:13, 28 August 2020

2020-08-28T03:13:12Z

EGadd: Forgot tto write about /cameraStop

2016-03-21T10:15:16Z

Forgot tto write about /cameraStop

EGadd at 23:13, 20 March 2016

2016-03-20T23:13:59Z

EGadd at 23:13, 20 March 2016

2016-03-20T23:13:43Z

EGadd: Created page with "Staxel has a camera built right in. This can be used to take some really nice and smooth cinematic shots. Remember, press 'i' on your keyboard to hide the UI. Don't want any o..."

2016-03-20T23:13:19Z

Created page with "Staxel has a camera built right in. This can be used to take some really nice and smooth cinematic shots. Remember, press 'i' on your keyboard to hide the UI. Don't want any o..."

New page

Staxel has a camera built right in. This can be used to take some really nice and smooth cinematic shots.
Remember, press 'i' on your keyboard to hide the UI. Don't want any of that pesky UI ruining your awesome shots!

Listed here are the commands needed to use the camera. Type the commands in message box (Press 'enter' on your keyboard and the message box will pop up).

----

/cameraCapture
This creates the first or any additional points on the camera path. When playing the camera path the camera will move to each point in the same order you captured them in.

----

/cameraSave shot_name
This command saves the shot so that it can be loaded another time. shot_name must be replaced with whatever you want to name the shot. You will use this name to load the camera later.

----

/cameraLoad shot_name
This command loads a previously saved camera path. Replace shot_name with the name of the camera path you want to load. Make sure to remember/write down the names of all the shots you've saved!

----

/cameraPlay 1 true
This command plays the currently loaded shot. The 1 is how many seconds the camera must take to move from one point to another. "true" means that the camera will loop, replace it with "false" if you don't want the camera to loop.

----

← Older revision		Revision as of 03:13, 28 August 2020
Line 35:		Line 35:

	If your camera is currently playing and you need to break out of it, enter this command		If your camera is currently playing and you need to break out of it, enter this command
		+
		+	----
		+
		+	/cameraReset
		+
		+	Completely clears out the previous path. Ready for you to start again.

	----		----

← Older revision		Revision as of 23:13, 20 March 2016
Line 4:		Line 4:
	Listed here are the commands needed to use the camera. Type the commands in message box (Press 'enter' on your keyboard and the message box will pop up).		Listed here are the commands needed to use the camera. Type the commands in message box (Press 'enter' on your keyboard and the message box will pop up).

		+	'''Commands'''

	----		----

← Older revision		Revision as of 10:15, 21 March 2016
Line 29:		Line 29:

	This command plays the currently loaded shot. The 1 is how many seconds the camera must take to move from one point to another. "true" means that the camera will loop, replace it with "false" if you don't want the camera to loop.		This command plays the currently loaded shot. The 1 is how many seconds the camera must take to move from one point to another. "true" means that the camera will loop, replace it with "false" if you don't want the camera to loop.
		+
		+	----
		+
		+	/cameraStop
		+
		+	If your camera is currently playing and you need to break out of it, enter this command

	----		----

@@ Line 8: / Line 8: @@
 /cameraCapture
 This creates the first or any additional points on the camera path. When playing the camera path the camera will move to each point in the same order you captured them in.
@@ Line 13: / Line 14: @@
 /cameraSave shot_name
 This command saves the shot so that it can be loaded another time. shot_name must be replaced with whatever you want to name the shot. You will use this name to load the camera later.
@@ Line 18: / Line 20: @@
 /cameraLoad shot_name
 This command loads a previously saved camera path. Replace shot_name with the name of the camera path you want to load. Make sure to remember/write down the names of all the shots you've saved!
@@ Line 23: / Line 26: @@
 /cameraPlay 1 true
 This command plays the currently loaded shot. The 1 is how many seconds the camera must take to move from one point to another. "true" means that the camera will loop, replace it with "false" if you don't want the camera to loop.
 ----